Instrument control package

Instrument-Control is a package by Andrius Sutas for interfacing the outside world of hardware via Serial, i2c or Parallel interfaces. It is currently under development, you can browse the SVN repository here.

Examples

Serial

Configuring interface

You might want to configure interface in a loopback mode for testing.

• If you have a Serial adapter, then simply connect pins 3 (Tx) and 2 (Rx) together (assuming your adapter is RS-232 DE9, otherwise check before doing anything). One can also insert an LED in series to view the actual bitstream.
• If you do not have a Serial adapter then create a virtual port using:

# socat PTY,link=/dev/ttyS15 PTY,link=/dev/ttyS16

which will open two interconnected interfaces, where one (e.g. /dev/ttyS15) can be opened in Octave and second (e.g. /dev/ttyS16) using something like GNU screen:

$ screen /dev/ttyS16 <baudrate>

do not forget to change interface permissions if you want to use them with Octave/screen without root privileges.

Parallel

Configuring interface

You will need to load following modules:

# modprobe parport
# modprobe ppdev

Now you should see devices like "/dev/parport0". In case you do not, you will need to create them manually and give sufficient privileges for your user:

# mknod /dev/parport0 c 99 0 -m 666

Example 1: LED trace

For this example you will need to connect 8 LEDs to Parallel interface Data port as shown below:

And then the actual script:

Code: trace.m

delay = 0.1; pp = parallel("/dev/parport0", 0); pp_data(pp, 0); pins = pow2([0, 1, 2, 3, 4, 5, 6, 7]); while 1 for p = pins pp_data(pp, p); sleep(delay); endfor # Reverse the order pins = pins(end:-1:1); endwhile pp_close(pp);

Run it and you should see LEDs "tracing" forwards and backwards.

Example 2: LED dimming a.k.a. PWM control

Use the same schematic as in Example 1.

Code: dim.m

delay = 0.00005; pp = parallel("/dev/parport0", 0); pp_data(pp, 0); dRange = 0:100; while 1 for duty = dRange pp_data(pp, 255); for dOn = 0:duty sleep(delay); endfor pp_data(pp, 0); for dOff = 0:(100-duty) sleep(delay); endfor endfor # Reverse order dRange = dRange(end:-1:1); endwhile pp_close(pp);

Run it and you should see LEDs changing brightness from lowest to maximum.

Example 3: Logic analyzer

We can surely make something more interesting, right? Enter basic logic analyzer.

Assume you are working with [this] temperature sensor. Something is not right. You do not have one of those expensive logic analyzers, but you do have a Parallel port! You remember that someone made a package for interfacing it with GNU Octave. So you connect your probes to appropriate Data port terminals and change settings accordingly. In this example:

Probe	Port terminal
!CS	DATA0
SCK	DATA1
SO	DATA2

NB: Parallel ports usually have weak pull-ups to +5V even when in "input" mode, so do not do this if unsure. One could potentially use different terminals in Control/Status ports to get true high-impedance inputs.

And write a simple script below:

Code: logic_analyzer.m

##################################################################### # Settings ##################################################################### # Channels to capture #channels = [0, 1, 2, 3, 4, 5, 6, 7]; channels = [2, 1, 0]; # Channel labels #channel = {"CH0"; "CH1"; "CH2"; "CH3"; "CH4"; "CH5"; "CH6"; "CH7"}; channel = {"SO"; "SCK"; "!CS"}; # Trigger channel triggerCh = 0; # When to trigger trigger = 0; # Capture on low. For high - 1 ##################################################################### samplesTime = []; samplesValue = []; #pp_close(pp); pp = parallel("/dev/parport0", 1); printf("Waiting for trigger...\n"); fflush(stdout); data = pp_data(pp); while (bitget(data, triggerCh + 1) != trigger) oldData = data; data = pp_data(pp); endwhile printf("Capturing...\n"); fflush(stdout); startTime = time(); samplesTime(end + 1) = 0; samplesValue(end + 1) = oldData; while (bitget(data, triggerCh + 1) == trigger) data = pp_data(pp); samplesTime(end + 1) = time() - startTime; samplesValue(end + 1) = data; endwhile # Statistics printf("Average sample rate: %f kHz\n", size(samplesValue)(2) / samplesTime(end) / 1000.0); pp_close(pp); # Plotting figure; for p = 1:size(channels)(2) subplot (size(channels)(2), 1, p) plot(samplesTime, bitget(samplesValue, channels(p) + 1)) ylabel(channel{p}); axis([-0.01, samplesTime(end)+ 0.01, -1, 2], "manual"); set(gca(), 'ytick', -1:2); set(gca(), 'yticklabel', {''; '0'; '1'; ''}); endfor xlabel ("t");

If connections and settings are correct you should see something like this:

i2c

i2c